With a minimal amount of training, one laborer can do
the work of 3 and do it three times faster! Water is
changed less frequently so there is less down time.
The Tileze 6000 will clean up to 1,000 square feet per
hour.
Electrically powered, the TILEZE 6000 employs a soft
sponge belt which picks grout up off the floor surface,
and is washed clean as it revolves around the rollers.
Residue and water are pressed out in the attached bucket
resulting in a clean, film-free surface. Only half the
amount of water is required, unlike conventional methods,
so grout joints are not washed out. Also, the operator
works in an upright position, eliminating fatigue and
stress on the knees and back.
The
TILEZE 6000 is equally at home on brick
pavers, abrasive tile, sure tread tile,
glazed and unglazed ceramic, rough slate,
natural stone, polished and unpolished marble
& granite, and Mexican tile.
The
TILEZE 6000 is powered by electric hand
drills which are serviceable in the USA
and Canada. Parts, including sponge belts
(regular & epoxy), are available directly
from Tile Eze or any authorized Tile Eze
dealer. Constructed of galvanized steel
with welded main frames, each model is virtually
maintenance-free. Movable parts have sealed
bearings for a smother operation, and belt
replacement is a snap - snap on, snap off.
Certain
grouts may create excessive foam in the water bucket,
making it necessary to change your water more often.
To eliminate this problem, we recommend using Tile Eze
Defoamer. One application of our defoamer will reduce
excess foam.
Read
all enclosed directions completely before operating
TILEZE 6000. We recommend practicing under controlled
conditions before going to a job site to gain the techniques
that ensure a professional job. The demonstration video
included with the machine should be viewed before use.
The TILEZE 6000 is designed to be used from left to
right. Start the job on the left side and move stroke
by stroke to the right to enhance the machine's performance.
Parts
List
20201 Chain Lock
40190 Sprocket for
Drill
40404 Motor
40504 Sprocket Z
18
45998 Bearing 6000
2RS
62024 Drive Shaft
400/620P
62030 Chain for Motor
62031 Double Sprocket
11/30
62032 Chain from
Sprocket to Rollers
62033 Sprocket Z
30
62034 Font Wheel
1 PC
62035 Wheel Set Front
3 PC
62036 Sponge Belt
Guide
62037 Sponge Belt
Roller Front
62038 Adjustment
Lifting Arm
62039 Adjust. Arm
Locking Device
62040 Driving Drum
Rubber Roller
62041 Upper Pressure
Roller
62042 Upper Pressure
Roller Arm
62043 Steering Handle
62044 On/Off Switch
62045 Rubber Grip
Set of 2
62046 Rear Swivel
Caster
62047 Pressure Clip
62048 Pressure Clip
Roll
62049 Inner Sponge
Belt Roller
62050 Lower Sponge
Belt Roller
Changing Sponge Belt
1.
Disconnect electrical supply.
2.
Remove water container.
3.
Loosen screw "A" and push top pressure
roller sideways.
4.
Loosen knob "B" and release height adjustment
by pressing button "C".
5.
Remove sponge glide control bar "D".
6.
Disconnect and remove wringer pressure roller "E".
7.
Place machine on it's left side and pull used sponge
off.
8.
Moisten new sponge (for easy replacement) and slide
onto machine.
9.
Lift machine back upright and line up/straighten
sponge belt over rollers.
10.
Insert "E" wringer roller set and place
into its holding studs.
11.
Fasten roller clips to studs with springs.
12.
Insert top pressure roller "E".
13.
Insert glide control bar "B".
14.
Lift handle bar up and tighten with knob "F".
15.
Replace water container.
16.
Check all connections.
Do
not run sponge when dry or overfill water container.
